Author Topic: 1/32 WNW Albatros D.V Richthofen (Read 32979 times)

Ryan · « **Reply #135 on:** February 12, 2019, 01:31:00 AM »

Thanks Lance, the front frames and engine bearers are actually glued to the left side of the fuselage, after careful dry fitting I found this could be done.
I think I wanted to get the loose assembly off my desk and into the model. Be careful though the rest of the assemblies have to mount per kit instructions.

The belts are quite a challenge and of course I really buggered mine and went with HGW.

Untitled by The 3rd Placer, on Flickr

Ryan

lcarroll · « **Reply #136 on:** February 12, 2019, 04:13:03 AM »

Thanks Ryan, now that you've successfully tested the water I'll give it a try!

Cheers,
Lance

RUREDI · « **Reply #137 on:** February 12, 2019, 07:56:55 PM »

Great stuff. Love watching your techniques and progress. Thanks for sharing.

Ryan · « **Reply #138 on:** February 12, 2019, 11:01:12 PM »

Thanks Rick, sometimes the techniques are trial and error (mostly error at times)!

Ryan

GAJouette · « **Reply #139 on:** February 13, 2019, 01:15:23 AM »

Ryan,
Outstanding progress my friend. I'm impressed with your wood painting skills for her interior. Keep up the high levels of excellence and the best of luck to you in the GB.
Highest Regards,
Gregory Jouette

Juan · « **Reply #140 on:** February 13, 2019, 02:49:24 AM »

That looks fantastic Ryan.

Ryan · « **Reply #141 on:** February 13, 2019, 03:28:21 AM »

Many thanks Juan and Gregory, much appreciated.

Ryan

lone modeller · « **Reply #142 on:** February 13, 2019, 07:06:45 AM »

Superb udates Ryan. As per usual your modelling skills are of the highestt order.

Stephen.

RAGIII · « **Reply #143 on:** February 13, 2019, 09:12:55 AM »

Really Looking excellent! Next update soon I hope

RAGIII

Ryan · « **Reply #144 on:** February 13, 2019, 10:51:11 PM »

Small update last evening.

Started detail painting the grey green clips and fixtures inside the fuselage. I've been doing a fair amount of brush painting on this model, and need to get back to masking and spraying.
The bracket above the black instrument was a bit troublesome to hand paint and detail.....would have been far easier to mask and paint at an earlier stage. Speaking of the black instrument I decided to attach now before the decal in case I had to use the face of the part to press into the tight fitting slot. The bolt heads were painted as well as the brass connector at the top of it.

Red Baron by The 3rd Placer, on Flickr

Red Baron by The 3rd Placer, on Flickr

Ryan

Ryan · « **Reply #145 on:** February 18, 2019, 07:34:26 AM »

Not a giant leap forward but I got a lot of detail painting and decals applied. Decals are fresh, so will need to clear coat once dry.

Red Baron by The 3rd Placer, on Flickr

Red Baron by The 3rd Placer, on Flickr

Ryan

RAGIII · « **Reply #146 on:** February 18, 2019, 10:18:53 AM »

The fuel selector panel and instrument look great! Looking forward to the next update!
RAGIII

Borsos · « **Reply #147 on:** February 18, 2019, 04:08:51 PM »

A very nice cockpit. Everything is perfectly painted and finished.
Andreas

Ryan · « **Reply #148 on:** February 18, 2019, 11:05:04 PM »

Thanks guys, the decals really set the parts off.

Ryan

pepperman42 · « **Reply #149 on:** February 19, 2019, 12:32:00 AM »

This is very nice clean work!! Great accenting

Steve