Thank you all!
RiggingFor mounting the upper wing I finished the inner struts:
![](https://drive.google.com/uc?export=view&id=0B1jvv6k_doLhV2Z2OXktWHN3cTg)
It was planned to glue them to the upper wing, but at the end I glued them to the fuselage and mounted then the wing.
![](https://drive.google.com/uc?export=view&id=0B1jvv6k_doLhSThhMmtJaFdPRHM)
Not so easy to fit the 8 brass pins at the same time. Don't forget to drill all the rigging holes before!
![](https://drive.google.com/uc?export=view&id=0B1jvv6k_doLhNWdiUEhvU3E1ZFE)
More details follows now: burned 0,3mm copper wire as fuel pipes.
![](https://drive.google.com/uc?export=view&id=0B1jvv6k_doLhOG1zTU5CZFpIQk0)
The cooler was connected with 0,8mm lead wire.
![](https://drive.google.com/uc?export=view&id=0B1jvv6k_doLhcUFVYV8tMGloR3M)
After adding the rudder horns the control wires with turnbuckles are added.
![](https://drive.google.com/uc?export=view&id=0B1jvv6k_doLhcHpIc2libDBZRGs)
The buckles are Gaspatch "one end".
![](https://drive.google.com/uc?export=view&id=0B1jvv6k_doLhYXBhZG9DN3BTNzA)
The skid is mounted too..
![](https://drive.google.com/uc?export=view&id=0B1jvv6k_doLhWXlnZmNHZ25yTDA)
A good preparation saves time and avoid losing the small parts: 10 turnbuckles type "Albatros" and brass pipes.
![](https://drive.google.com/uc?export=view&id=0B1jvv6k_doLhTHZJbm1xOVFuV28)
Wit that preparation I added 12 rigging wires within one and a half hours.
![](https://drive.google.com/uc?export=view&id=0B1jvv6k_doLhTjJ2NjFMTTBScEU)
Burned 0,5mm brass piped was widened with a needle ...
![](https://drive.google.com/uc?export=view&id=0B1jvv6k_doLhU2Zwb1JULWUyTTA)
... and added to the cooler.
![](https://drive.google.com/uc?export=view&id=0B1jvv6k_doLhLU5NbTUzc1ljYTQ)
Further details: decals on wing and air screw, water pipes painted dark grey, exhaust and counter surface for the struts added.
![](https://drive.google.com/uc?export=view&id=0B1jvv6k_doLhZ0NZbG80cGRGNnM)
Finished the gear, with adding the springs made from lead wire and PE stopper.
![](https://drive.google.com/uc?export=view&id=0B1jvv6k_doLheXl6blQybDNHY2c)
After mounting the gear two rigging lens with turnbuckles are added, so that its the actual state:
![](https://drive.google.com/uc?export=view&id=0B1jvv6k_doLha1RwNnFoSHJCVlk)
Not so much work left for completion:
![](https://drive.google.com/uc?export=view&id=0B1jvv6k_doLhT0lZTWdnUXo5Y2s)
Thank you for your interest!
Cheers,
Frank