Author Topic: CSM Nieuport 11 Early (Read 1279 times)

RAGIII · « **on:** April 02, 2025, 08:29:51 AM »

I have begun work on the CSM Nieuport 11 early to be finished in the N3 scheme. The kit engine was assembled OOb, still lots of time to build up the courage to do the 3D printed version. Interior side panels, floor, and seat have been done in oils over a Polyscale Deck Tan base. Raw sienna and Burnt umber were used.
RAGIII

The engine is he kit plastic version. I still have lots of time to think about attempting the 3D version

Radarman · « **Reply #1 on:** April 02, 2025, 11:58:46 AM »

RAGIII,
It's great to see you dive in to this one.

Happy Modeling, Kevin

NigelR · « **Reply #2 on:** April 02, 2025, 06:09:45 PM »

Lovely start Rick, you will enjoy this one (apart from the blue edging tapes.......

)

andonio64 · « **Reply #3 on:** April 02, 2025, 06:29:46 PM »

Great start Rick, I look forward to following your progresses!

Have a nice day!

AngryJazz · « **Reply #4 on:** April 03, 2025, 06:23:29 PM »

Nice start! Will be a stunner

RAGIII · « **Reply #5 on:** April 04, 2025, 12:24:41 AM »

Quote from: Radarman on April 02, 2025, 11:58:46 AM

RAGIII,
It's great to see you dive in to this one.

Happy Modeling, Kevin

Thanks Kevin!
RAGIII

Quote from: NigelR on April 02, 2025, 06:09:45 PM

Lovely start Rick, you will enjoy this one (apart from the blue edging tapes....... )

When working with Edgar to get the replacement decal for the Bristol Scout, I ordered the Mask set for this one. It "Should" make those edge tapes easier to paint

RAGIII

Quote from: andonio64 on April 02, 2025, 06:29:46 PM

Great start Rick, I look forward to following your progresses!

Have a nice day!

Thanks for dropping in Antonio!
RAGIII

Quote from: AngryJazz on April 03, 2025, 06:23:29 PM

Nice start! Will be a stunner

I appreciate your confidence in My abilities

RAGIII

Allan31 · « **Reply #6 on:** April 04, 2025, 02:03:35 AM »

Great start. I wouldn't fret over the 3D printed engine, yours looks terrific.

Borsos · « **Reply #7 on:** April 04, 2025, 02:46:53 AM »

Great start, Rick! You?ll have fun with that kit!
Andreas

RAGIII · « **Reply #8 on:** April 05, 2025, 09:40:04 AM »

Quote from: Allan31 on April 04, 2025, 02:03:35 AM

Great start. I wouldn't fret over the 3D printed engine, yours looks terrific.

Thanks and the funny thing is it's not constructing the 3D engine that is daunting. It is removing the parts from the 3D runners

RAGIII

Quote from: Borsos on April 04, 2025, 02:46:53 AM

Great start, Rick! You?ll have fun with that kit!
Andreas

Thanks Andreas. I have fun with all of My builds...even if they don't measure up to some of the More Talented Modelers here!
RAGIII

Alexis · « **Reply #9 on:** April 05, 2025, 05:05:36 PM »

Will be tagging along on tis adventure Rick . I do like the wood tones which you achieved and super job on the kit engine !

Alexis

Borsos · « **Reply #10 on:** April 05, 2025, 09:37:31 PM »

Quote

the funny thing is it's not constructing the 3D engine that is daunting. It is removing the parts from the 3D runners

The plastic engine looks very nice. But I actually waited to build the 3D printed engine on my Nieuport until I could not postpone the engine issue even longer because of the very same reasons
In the end I simply removed the parts by carefully breaking them off the printing gates with some pliers. That was all. No breakage and nothing as the printing gates are very delicate.

Boch · « **Reply #11 on:** April 07, 2025, 07:00:19 AM »

I am sitting in the audience with pleasure. There will be something to admire. Italian aviation is often on the sidelines, which is a pity.

Lukasz

xan · « **Reply #12 on:** April 07, 2025, 05:02:56 PM »

Great! I take a seat!!