Lukgraph Hanriot HD-1 and HD-2

[Jamo]

For further inspiration to build a Hanriot, have a look these hi-res images covering TVAL's original, restored Hanriot HD1:
https://jamesfahey.smugmug.com/Hanriot-HD1/

[Eric Armstrong]

For further inspiration to build a Hanriot, have a look these hi-res images covering TVAL's original, restored Hanriot HD1:
https://jamesfahey.smugmug.com/Hanriot-HD1/

Really nice photos.  I had no idea how close the air intakes for the carburetor and the fuel tank were to the pilot.  It's practically in his lap!

[bobs_buckles]

James,
 Thanks for the pictures.
Is this the Hanriot that came over from the RAF museum Hendon?

Cheers,
Bob
 

[Pup7309]

  CSM  ;Hanriot HD1 and Lukgraph HD2 - we live in good times 

[Jamo]

James,
 Thanks for the pictures.
Is this the Hanriot that came over from the RAF museum Hendon?

Cheers,
Bob

Yes it is Bob. TVAL sent across an Albatros DVa, an RE8 and a Sopwith Snipe (non-flyable) and in return received a Farman F40 (which needed restoration), the Hanriot (which didn't need too much done to become flyable again) and a very decrepit Sopwith 1 1/2 Strutter. Not sure if there was any more involved in the swap, maybe some parts etc

[Mike Norris]

Hi all,
Final renders of the Hanriot HD-1 and HD-2 float in 1:32 scale (there will also be a HD-2 wheeled version).

Mike

[Naimbs]

Hi,

You'll have to watch out for the carburettor outlet on the sides of the Hanriot HD.2 hood (I'm not sure if I'm wrong about the function of these tube outlets).

It was not positioned in the same place as the Hanriot HD.1.

Eduard had made the same mistake.

Arnaud

[Mike Norris]

Hi,

You'll have to watch out for the carburettor outlet on the sides of the Hanriot HD.2 hood (I'm not sure if I'm wrong about the function of these tube outlets).

It was not positioned in the same place as the Hanriot HD.1.

Eduard had made the same mistake.

Arnaud

[Naimbs]

Hi,

You'll have to watch out for the carburettor outlet on the sides of the Hanriot HD.2 hood (I'm not sure if I'm wrong about the function of these tube outlets).

It was not positioned in the same place as the Hanriot HD.1.

Eduard had made the same mistake.

Arnaud

Hello Mike,

[Mike Norris]

Hi Arnaud,
I should have stated why I posted the photograph 
It was to show the carburettor air intake position, as you correctly pointed out 

Mike

[KiwiZac]

Gosh that looks pretty.

[jeroen_R90S]

Regarding the HD-2, that large hatch looks different from the HD-1 as well.
The renders look nice, although I freely admit I just can't warm up to the Hanriot... I am really happy for those that have been waiting for a long time for a model of this aircraft!

Jeroen

[Mike Norris]

Hi all,
Hanriots HD.1/HD.2 - now available for pre-order
HD.1 (Le Rhone 9J engine)

https://lukgraph.pl/en_GB/p/Hanriot-HD.1-132-Pre-order/241

HD.2 Float version (Clerget 9B engine)

https://lukgraph.pl/.../Hanriot-HD.2-FLOAT-132-Pre-order/244

HD.2 wheels version (Clerget 9B engine)

https://lukgraph.pl/en_GB/p/Hanriot-HD.2-132-Pre-order/242

Kit-set contains:
Resin Casting Parts:
Fuselage, wings (steel wire reinforced), horizontal and vertical fins, ailerons, tail wings, floats (HD2)
3D printed parts:
Full Interior, propeller, guns (2 pcs.), undercarriage.
All struts, ABS resin printed with holes to easier connect parts with wire.
3D printed parts packed in an additional box to ensure maximum protection.
- photo-etched parts (over 100 pcs.)
- steel  wire to connect wings (1.2mm) and copper wires (0.5, 0.3mm)
- Windscreen - PE+film
- Decals 8 schemes for HD.1
- Decals 5 schemes for HD.2 wheel version
- Decals 4 schemes for HD.2 Float
- Colored instructions

Mike

[Juan]

Beautifully done by Lukgraph.  Will wait to see what CSM offers as resin is not really my thing.  All the best to Lukgraph.

[KiwiZac]

Is it too early to write to Santa? I have, after all, been a good boy 

I'm very excited to see these kits in the wild and on the forum.