forum.ww1aircraftmodels.com
WW1 Aircraft Modeling => Under Construction => Topic started by: xmald on August 04, 2018, 09:47:42 PM
-
Hello,
I`m starting another project, I`m going to use the Aviattic`s PC10 and CDL decals for the beastie. More pics soon.
Here`s my inbox review of them (in Polish) if anyone`s interested:
http://www.kfs-miniatures.com/ (http://www.kfs-miniatures.com/)
(https://i.imgur.com/oKmkg7f.jpg)
(https://i.imgur.com/8UoW0yn.jpg)
-
Hi Filip, looking forward to your treatment on this awesome subject.
-
Aviattic`s decals review (in Polish) at: http://www.kfs-miniatures.com/1-32-linen-effect-decals-wal…/
I`ve completed the instrument panel with added petrol lines. Also, the turnbuckles were added to the rudder bar and the control stick.
(https://i.imgur.com/tOfPgGD.jpg)
(https://i.imgur.com/BtjD8Rb.jpg)
-
Nice! I will watch to see in this big scale, which details I missed on mine.
Hope to be able to finish it in the next weeks (so a mini group build) ;)
Cheers,
Frank
-
Outstanding start on the interior. I am looking forward to more as always!
RAGIII
-
Good start. I will watch with high interest.
Bye
Manni
-
I also like the way you started. Thata very promising beginning.
Best regards
Andreas
-
Looking excellent so far -how did you paint the "matting" in the gunner's position?
-
Many thanks for your kind words!
Looking excellent so far -how did you paint the "matting" in the gunner's position?
It`s been painted with oils, clear yellow/orange mix and DUST Oilbrusher on top of it. After that clear varnish and brown wash were applied.
The cockpit is almost ready. I`ve added some smaller scratch-built details like the magneto switch or the petrol installation plumbing.
(https://i.imgur.com/V4LhWhN.jpg)
(https://i.imgur.com/IOrMitP.jpg) (https://i.imgur.com/o711T9h.jpg) (https://i.imgur.com/k36dSQL.jpg) (https://i.imgur.com/DdVA1NS.jpg) (https://i.imgur.com/NUlDFP0.jpg)
-
Thanks, it looks superb (as does the rest, obviously!)
Jeroen
-
Superb work!
RAGIII
-
Great progress, Filip. Which colour scheme are you planning?
-
Thanks a lot! Przemek it`s going to be "T" D8084 with the red stripes on the upper wing. I`m not very fond of the Brisfits with the four-bladed props, so my choice was somewhat limited.
The cockpit is almost completed. I`ve decided to replace the original seatbelts with the HGW aftermarket ones. They are extremely good and much more to scale.
(https://i.imgur.com/QbuGvd5.jpg)
(https://i.imgur.com/GpwQXKK.jpg)
(https://i.imgur.com/zuAu6i1.jpg)
(https://i.imgur.com/0OmnFqm.jpg)
-
Pure perfection, Filip! Your usual wizardry!
Cheers,
Bud
-
It looks great!
So much of this work will be gone forever when it's buttoned up though!
I wish WNW would pump out just 1 "skeleton" model with all the guts showing. I think they are much more visually interesting than the closed up models in these early stages of construction.
I realize most modelers might not prefer that, but not sure why 1 or 2 kits couldn't be build in this way.
Mix it up a little!
-
Pure perfection, Filip! Your usual wizardry!
Cheers,
Bud
Plus One Amigo!
RAGIII
-
Pure perfection, Filip! Your usual wizardry!
Cheers,
Bud
Plus One Amigo!
RAGIII
Add me to the collection! Outstanding :o
von B
-
Thanks a lot!!!
Apart from the two cross-section wires, the cockpit is ready to be installed into the fuselage. I`ve added a map and the gloves to the gunner`s seat.
(https://i.imgur.com/jUSTvyC.jpg)
(https://i.imgur.com/Paf5iZt.jpg)
(https://i.imgur.com/1fyCJRM.jpg)
(https://i.imgur.com/aATrXbZ.jpg)
(https://i.imgur.com/tCfW29X.jpg)
(https://i.imgur.com/MwZd47b.jpg)
-
Stunning interior work Filip!
RAGIII
-
the gloves are a very nice addition, how did you make them??
-
Beautiful interiors and the small additions are a great touch.
Ciao
Giuseppe
-
Great work!
Guy
-
Magnificent to this point Filip! This is Wingnut's best Kit in my opinion, you are doing it justice and more. I'll add myself to the list of those asking how on earth you did the gunner's gloves, a fully functional 1:32 Scale sewing machine possibly?? ;)
Cheers,
Lance
-
Magnificent !!!
Spyros
-
Interior is masterpiece :)
Adam.
-
Many thanks!!!
The first pieces of Aviattic`s CDL decals have been applied. I must admit they are beyond my expectations - simply gorgeous. The fuselage is glued together.
(https://i.imgur.com/0ywMvdn.jpg)
(https://i.imgur.com/l72Q5fY.jpg)
(https://i.imgur.com/tarYKEg.jpg)
-
Looking fantastic Filip.
-
Your different textures are rendered so beautifully.
Cheers
Sud
-
Superb weathering and top notch photography.
Ryan
-
Outstanding application and weathering with the Aviattic decals!
RAGIII